真人做爰直播 在线看


Our company specializes in producing crawler type shot blasting machine, hook type shot blasting machine, catenary shot blasting machine, steel plate, steel structure shot blasting machine, through shot blasting machine and so on. We can also make non-standard customization according to the characteristics of the product. We only need one phone to provide you with the appropriate technical solution free of charge. Enquiry Hotline: 0515-88323729

真人做爰直播 在线看

Industry news
Spot supply! 6 throwing head roller pass shot blasting machine for steel and steel pipe surface rust removal and oxidation coating to increase adhesion.
Time: 2020-05-20 10:42:32 Source: How much is the roller pass shot blasting machine? Author: Roller pass blasting machine manufacturers

 6 throwing head through shot blasting machine.Jpg

Spot supply! 6 throwing head roller pass type shot blasting machine is used for rust removing and oxide coating increasing on the surface of the steel and steel pipe. The roller type shot blasting machine transfers the workpiece to the blast cleaning room for conveying the roller table, while blasting the ball to remove rust, blasting the sand continuously, removing dust from the process of blasting, removing the dust from the dust collector, and automatically recovering the steel ball and steel grit. It's still a good brand.

1, roller frequency control: frequency conversion and positive inversion;

2. The dust removal system is equipped with 1 new high efficiency LT-12 pulse blowback cleaning cartridge type dust remover, which has high dust removal efficiency and convenient installation and maintenance.

3. The shot blasting chamber adopts the steel and plate riveting structure, with reasonable structure, high strength and good rigidity.

4, the body is equipped with wear resistant plate, wear resistance, impact resistance, long service life.

5. Use the labyrinth seal to prevent the projectile from flying out.

6, equipment is equipped with safety protection devices to ensure safe and effective work.

Shot blasting machine is the key part of roller pass shot blasting machine. The prominent problem in the use of shot blasting machine is the wear of parts. The blades, the pellet wheel and the directional sleeve are all vulnerable parts and need to be replaced frequently. The transmission device of the shot blasting device is composed of a belt wheel at one end of the transmission shaft and a power supply. Matters needing attention in the installation of shot blasting machine:

1 the shot blasting device should be installed on a firm stand.

2 the spindle bearing of the shot blasting machine is added with calcium grease twice a week. The amount of refueling is not easy. Every 3-6 months, the new grease should be replaced.

3 after each shot, the shot blasting machine should inspect the wear condition of the worn parts and replace the worn parts in time.

4 when the blaster blade is not completely stopped, the shield cover is not allowed. When opening the cover, all the buttons should be cut off.

5 after assembly, the surface runout is not greater than 0.05 mm, and the radial runout is not greater than 0.1 mm.

After the shot blasting machine is assembled, it must have very high accuracy of geometric tolerance. Every shot blasting device we produced is strictly tested and controlled by weight. The weight balance of the balance ensures that the shot blasting machine has good dynamic balance performance, and the unbalanced torque is less than 15Nmm, thereby reducing the noise of the equipment.

6 the thrower roller pass type shot blasting machine is to hang the workpiece on the roller table and feed the conveying roller to move the workpiece forward. When the workpiece enters the cleaning room, the shot blasting device starts to work sequentially.

6 through the shot blasting machine, the surface oxide, dirt and other attachments on the steel surface are cleaned up, and the treated surface can reach Sa2.5-3.0 level. The working mode of the shot blasting machine is continuous circulation. When the shot blasting time reaches the requirement, the shot blasting machine stops working automatically.

Roller pass type shot blasting machine works continuously and continuously deoxidization, cleaning and pretreatment of all kinds of steel materials, such as steel plate, steel, steel beam, section steel, steel pipe and cast steel.

It is easy to operate. Only loading steel material on the machine, pressing the start button, after a short cycle period, the system automatically disposes of the processed material, that is, the entire cleaning process is completed, and all the dust and residual pellets are removed.

Application: for all kinds of steel materials, such as steel plate, steel, steel beam, section steel, steel pipe and cast steel.